- Out-of-Stock
Painting of pools in water
Painting of water-based swimming pools of the highest qualitySuitable for protection of swimming pools whose surfaces are cement mortar and other derivatives.
Surface preparation
Surfaces should be sanded, clean, dry, free of dust, grease, oils and moisture. On unpainted surfaces: Sand, clean, brush, remove dust, grease, oil, saltpeter, scale, mold and other elements that can affect the anchorage and leave preferably with roughness to improve adhesion. On surfaces with old paint: Remove paint in poor condition and proceed as on unpainted surface. Apply the following preparations: On surfaces of cement mortars and derivatives, either dry and set: Apply the same product or as a preparation, apply SELLAFOND TO WATER (Ref. 1894) or SELLAFOND (Ref. 1764). On surfaces of cement mortars in poor condition, with lime, saltpeter, etc: Remove lime and saltpeter and seal properly with SELLAFOND (Ref. 1764). On steel and iron: Apply WHITE ANTIOXIDANT PRIMER (Ref. A1960). On galvanized and light metals: Apply WHITE MULTI-ADHERENT PRIMER (Ref. A1994). Then apply two minimum layers of product.
Before applying
Application temperature: Higher than 5ºC. Support temperature: Higher than 5ºC. Ambient relative humidity: Less than 80%. Support humidity: Less than 6%.
How to use
Remove the contents of the container well. Apply with good air renewal, in thin, uniform and well-extended layers. Recommendations before applying. Do not apply to the direct sun, or with morning spray. Add water to the pool after a week of application. New pool: Allow a month to pass, once built, before painting. Percentage of application: Brush and Roller: Water, 1st hand diluted 10-15%. Other in use or slightly diluted (maximum 5%). Airless gun, depending on the nozzle and pressure chosen.
Storage
Store in a cool place. Do not store open or started containers.
Calculate how much you need:
Suitable for protection of swimming pools whose surfaces are cement mortar and other derivatives.
Surface preparation
Surfaces should be sanded, clean, dry, free of dust, grease, oils and moisture. On unpainted surfaces: Sand, clean, brush, remove dust, grease, oil, saltpeter, scale, mold and other elements that can affect the anchorage and leave preferably with roughness to improve adhesion. On surfaces with old paint: Remove paint in poor condition and proceed as on unpainted surface. Apply the following preparations: On surfaces of cement mortars and derivatives, either dry and set: Apply the same product or as a preparation, apply SELLAFOND TO WATER (Ref. 1894) or SELLAFOND (Ref. 1764). On surfaces of cement mortars in poor condition, with lime, saltpeter, etc: Remove lime and saltpeter and seal properly with SELLAFOND (Ref. 1764). On steel and iron: Apply WHITE ANTIOXIDANT PRIMER (Ref. A1960). On galvanized and light metals: Apply WHITE MULTI-ADHERENT PRIMER (Ref. A1994). Then apply two minimum layers of product.
Before applying
Application temperature: Higher than 5ºC. Support temperature: Higher than 5ºC. Ambient relative humidity: Less than 80%. Support humidity: Less than 6%.
How to use
Remove the contents of the container well. Apply with good air renewal, in thin, uniform and well-extended layers. Recommendations before applying. Do not apply to the direct sun, or with morning spray. Add water to the pool after a week of application. New pool: Allow a month to pass, once built, before painting. Percentage of application: Brush and Roller: Water, 1st hand diluted 10-15%. Other in use or slightly diluted (maximum 5%). Airless gun, depending on the nozzle and pressure chosen.
Storage
Store in a cool place. Do not store open or started containers.
Data sheet
- Family
- Paint for swimming pools and sports courts
- Surface
- Pools
- Feature Listed 1
- DURABLE, RESISTANT AND HARD FINISHES.
- Feature listed 2
- ANTI-ALGAE EFFECT
- Subname
- Painting of water-based swimming pools of the highest quality
- Feature listed 3
- Ease of application.
- Barpicolor
- No
- Featured product 1
- Durable, resistant and hard finishes.
- Featured product 2
- Anti-algae effect
- Featured product 3
- Ease of application.
- Featured product 4
- The high chemical stability of its composition makes it ideal to resist the continuous action of water and its disinfection and conservation treatments.
- i-dilution
- Water
- i-t.drying
- 30min
- i-t.repainted
- 5hours
- i-performance
- 6-8m2/L
- i-n layers
- 2
- I calculate performance
- 7
- Water / solvent
- Water
- I calculate layers
- 2
- s-certificate euroclasses 1
- No
- s-certified slippage 2
- No
- s-certified anticorrosive enamels 3
- No
- s-certified mushrooms 4
- No
- s-bacterial certificate 5
- No
- s-certificate guarantee three 6
- No
- s-certificate warranty five 7
- No
- s-certificate guarantee seven 8
- No
- s-certificate guarantee eight 9
- No
- s-certificate guarantee ten 10
- No
- s-certificate guarantee fifteen 11
- No
- s-certificate A 12
- No
- s-certificate A+ 13
- No
- s-certificate B 14
- No
- s-certificate C 15
- No
- s-certificate anti-mold preservative 16
- No
- s-certified UV filter 17
- No
- s-ecolabel 18 certificate
- No
- s-CE certificate 19
- No
- s-certificate anticarbonation 20
- No
- s-certificate Pliolite 21
- No
- s-certificate cidemco 22
- No